 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| LTC4069 Standalone 750mA Li-Ion Battery Charger in 2 x 2 DFN with NTC Thermistor Input DESCRIPTIO The LTC(R)4069 is a complete constant-current/constantvoltage linear charger for single-cell lithium-ion batteries. The 2mm x 2mm DFN package and low external component count make the LTC4069 especially well-suited for portable applications. Furthermore, LTC4069 is specifically designed to work within USB power specifications. The CHRG pin indicates when charge current has dropped to ten percent of its programmed value (C/10). An internal timer terminates charging according to battery manufacturer specifications. No external sense resistor or blocking diode is required due to the internal MOSFET architecture. Thermal feedback regulates charge current to limit the die temperature during high power operation or high ambient temperature conditions. When the input supply (wall adapter or USB supply) is removed, the LTC4069 automatically enters a low current state, dropping battery drain current to less than 1A. With power applied, LTC4069 can be put into shutdown mode, reducing the supply current to less than 20A. The LTC4069 also includes automatic recharge, lowbattery charge conditioning (trickle charging), soft-start (to limit inrush current) and an NTC thermistor input used to monitor battery temperature. The LTC4069 is available in a tiny 6-lead, low profile (0.75mm) 2mm x 2mm DFN package. Complete Charge Cycle (1000mAh Battery) 600 500 CHARGE CURRENT (mA) FEATURES Complete Linear Charger in 2mm x 2mm DFN Package C/10 Charge Current Detection Output Timer Charge Termination Charge Current Programmable up to 750mA with 5% Accuracy No External MOSFET, Sense Resistor or Blocking Diode Required NTC Thermistor Input for Temperature Qualified Charging Preset 4.2V Float Voltage with 0.6% Accuracy Constant-Current/Constant-Voltage Operation with Thermal Feedback to Maximize Charge Rate Without Risk of Overheating Charge Current Monitor Output for Gas Gauging Automatic Recharge Charges Single Cell Li-Ion Batteries Directly from USB Port 20A Supply Current in Shutdown Mode Soft-Start Limits Inrush Current Tiny 6-Lead (2mm x 2mm) DFN Package APPLICATIO S Wireless PDAs Cellular Phones Portable Electronics , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents including 6522118, 6700364. TYPICAL APPLICATIO VIN 4.3V TO 5.5V RNOM 100k VCC R1 510 Standalone Li-Ion Battery Charger 500mA BAT CONSTANT CURRENT 400 300 200 100 LTC4069 CHRG PROG NTC GND RPROG 2k 4069 TA01 + 4.2V Li-Ion BATTERY RNTC 100k 1F 0 VCC = 5V RPROG = 2k 0 0.5 1 1.5 2 2.5 3 3.5 4 TIME (HOURS) 4.5 5 U U U 4.50 CONSTANT VOLTAGE 4.25 BATTREY VOLTAGE (V) CHARGE TRANSITION 4.00 3.75 3.50 3.25 3.00 CHARGE TERMINATION 4069 TA01b 4069f 1 LTC4069 ABSOLUTE (Note 1) AXI U RATI GS PACKAGE/ORDER I FOR ATIO TOP VIEW GND 1 CHRG 2 BAT 3 7 6 PROG 5 NTC 4 VCC VCC t < 1ms and Duty Cycle < 1% ................. - 0.3V to 7V Steady State ........................................... - 0.3V to 6V BAT, CHRG ................................................. -0.3V to 6V PROG, NTC ..................................... -0.3V to VCC + 0.3V BAT Short-Circuit Duration ...........................Continuous BAT Pin Current ................................................. 800mA PROG Pin Current ............................................... 800A Junction Temperature (Note 6) ............................ 125C Operating Temperature Range (Note 2) .. - 40C to 85C Storage Temperature Range ................ - 65C to 125C DC PACKAGE 6-LEAD (2mm x 2mm) PLASTIC DFN TJMAX = 125C, JA = 60C/W (NOTE 3) EXPOSED PAD (PIN 7) IS GND MUST BE SOLDERED TO PCB ORDER PART NUMBER LTC4069EDC DC PART MARKING LBZX Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25C. VCC = 5V, VBAT = 3.8V, VNTC = 0V unless otherwise specified. (Note 2) SYMBOL VCC ICC ICCMS ICCUV VFLOAT IBAT IBMS IBUV VUVLO VPROG VASD IPROG PARAMETER VCC Supply Voltage Quiescent VCC Supply Current VCC Supply Current in Shutdown VCC Supply Current in Undervoltage Lockout VBAT Regulated Output Voltage BAT Pin Current Battery Drain Current in Shutdown Mode CONDITIONS (Note 4) VBAT = 4.5V (Forces IBAT and IPROG = 0) Float PROG VCC < VBAT, VCC = 3.5V, VBAT = 4V IBAT = 2mA IBAT = 2mA, 0C < TA < 85C RPROG = 10k (0.1%), Current Mode RPROG = 2k (0.1%), Current Mode Floating PROG, VCC > VBAT MIN 3.75 TYP 120 20 6 MAX 5.5 250 40 11 4.225 4.242 112 525 1 4 3.8 3.2 1.02 1.02 100 45 UNITS V A A A V V mA mA A A V V V V mV mV A 4.175 4.158 88 475 -1 0 3.4 2.8 0.98 0.98 60 15 4.2 4.2 100 500 0 1 3.6 3.0 1 1 82 32 3 Battery Drain Current in Undervoltage VCC = 3.5V, VBAT = 4V Lockout VCC Undervoltage Lockout Voltage PROG Pin Voltage Automatic Shutdown Threshold Voltage PROG Pin Pull-Up Current VCC Rising VCC Falling RPROG = 2k, IPROG = 500A RPROG = 10k, IPROG = 100A (VCC - VBAT), VCC Low to High (VCC - VBAT), VCC High to Low VPROG > 1V 2 U 4069f W U U WW W LTC4069 ELECTRICAL CHARACTERISTICS The denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25C. VCC = 5V, VBAT = 3.8V, VNTC = 0V unless otherwise specified. (Note 2) SYMBOL VMS,PROG tSS ITRKL VTRKL VTRHYS VRECHRG VUVCL1 VUVCL2 tTIMER PARAMETER PROG Shutdown Threshold Voltage Soft-Start Time Trickle Charge Current Trickle Charge Threshold Voltage Trickle Charge Hysteresis Voltage Recharge Battery Threshold Voltage (VCC - VBAT) Undervoltage Current Limit Termination Timer Recharge Timer Low-Battery Trickle Charge Time VCHRG ICHRG IC/10 TLIM RON fBADBAT DBADBAT INTC VCOLD VHOT VNTC-DIS VDIS-HYS fNTC DNTC CHRG Pin Output Low Voltage CHRG Pin Leakage Current End of Charge Indication Current Level Junction Temperature in Constant Temperature Mode Power FET "ON" Resistance (Between VCC and BAT) Defective Battery Detection CHRG Pulse Frequency Defective Battery Detection CHRG Pulse Frequency Duty Ratio NTC PIN Current Cold Temperature Fault Threshold Voltage Hot Temperature Fault Threshold Voltage NTC Disable Threshold Voltage NTC Disable Hysteresis Voltage Fault Temperature CHRG Pulse Frequency Fault Temperature CHRG Pulse Frequency Duty Ratio VNTC = 2.5V Rising Voltage Threshold Hysteresis Falling Voltage Threshold Hysteresis Falling Threshold; VCC = 5V 0.76 * VCC 0.015 * VCC 0.35 * VCC 0.017 * VCC 82 50 2 20 IBAT = 350mA VBAT = 2.5V ICHRG = 5mA VBAT = 4.5V, VCHRG = 5V RPROG = 2k (Note 5) VFLOAT - VRECHRG, 0C < TA < 85C IBAT = 90% Programmed Charge Current IBAT = 10% Programmed Charge Current CONDITIONS VPROG Rising VBAT = 2V, RPROG = 2k (0.1%) VBAT Rising MIN 3.7 35 2.7 70 180 90 3 1.5 0.75 TYP 4 170 50 2.9 90 100 220 125 4.5 2.25 1.125 60 0 MAX 4.3 65 3.05 130 330 150 6 3 1.5 105 1 0.11 UNITS V s mA V mV mV mV mV Hrs Hrs Hrs mV A mA/mA C m Hz % 0.08 0.095 115 450 2 80 1 A V V V V mV mV Hz % Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The LTC4069 is guaranteed to meet performance specifications from 0C to 70C. Specifications over the -40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Failure to solder the exposed backside of the package to the PC board ground plane will result in a thermal resistance much higher than rated. Note 4: Although the LTC4069 functions properly at 3.75V, full charge current requires an input voltage greater than the desired final battery voltage per the VUVCL1 specification. Note 5: IC/10 is expressed as a fraction of measured full charge current with indicated PROG resistor. Note 6: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 4069f 3 LTC4069 TYPICAL PERFOR A CE CHARACTERISTICS Battery Regulation (Float) Voltage vs Battery Charge Current 4.24 4.23 4.22 VFLOAT (V) VCC = 5V TA = 25C RPROG = 2k 4.24 4.23 4.22 VFLOAT (V) 4.20 4.19 4.18 4.17 4.16 0 100 200 300 IBAT (mA) 400 500 4069 G01 4.20 4.19 4.18 4.17 4.16 -50 - 25 50 25 TEMPERATURE (C) 0 75 100 4069 G02 VFLOAT (V) 4.21 Charge Current vs Supply Voltage (Constant Current Mode) 200 175 150 RPROG = 10k VBAT = 3.8V TA = 25C IBAT (mA) IBAT (mA) 125 100 75 50 25 300 200 100 0 IBAT (mA) 0 4 4.5 5 5.5 SUPPLY VOLTAGE (V) 6 4069 G04 PROG Pin Voltage vs Temperature (Constant Current Mode) 1.02 VCC = 5V VBAT = 3.8V RPROG = 10k 1.01 VPROG (V) VPROG (V) 1.00 0.6 0.4 RDS (m) 0.99 0.98 -50 -25 50 25 0 TEMPERATURE (C) 4 UW 75 100 4069 G07 Battery Regulation (Float) Voltage vs Temperature 4.24 4.23 4.22 4.21 4.20 4.19 4.18 4.17 4.16 Battery Regulation (Float) Voltage vs Supply Voltage TA = 25C IBAT = 2mA RPROG = 2k 4.21 4 5 4.5 5.5 SUPPLY VOLTAGE (V) 6 4069 G03 Charge Current vs Battery Voltage 600 500 400 VCC = 5V TA = 25C RPROG = 2k 600 500 400 300 200 100 Charge Current vs Ambient Temperature with Thermal Regulation (Constant Current Mode) THERMAL CONTROL LOOP IN OPERATION 0 1 2 3 VBAT (V) 4 5 4069 G05 0 -50 VCC = 5V VBAT = 3.8V RPROG = 2k 0 100 50 TEMPERATURE (C) 150 4069 G06 PROG Pin Voltage vs Charge Current 1.2 1.0 0.8 450 Power FET On Resistance vs Temperature 550 VCC = 4V IBAT = 400mA VCC = 5V TA = 25C RPROG = 2k 500 400 0.2 0 0 100 200 300 IBAT (mA) 400 500 4069 G08 350 300 -50 -25 0 25 50 TEMPERATURE (C) 75 100 4069 G09 4069f LTC4069 TYPICAL PERFOR A CE CHARACTERISTICS Undervoltage Lockout Threshold Voltage vs Temperature 4.00 3.75 RISE 3.50 40 60 50 IBAT (mA) 3.25 3.00 2.75 2.50 -50 FALL 30 20 10 0 IBAT (mA) VCC (V) -25 50 0 25 TEMPERATURE (C) CHRG Pin Output Low Voltage vs Temperature 140 120 VCC = 5V ICHRG = 5mA 100 TIMER ACCURACY (%) VCHRG (mV) -2 -3 -4 -5 -6 TIMER ACCURACY (%) 80 60 40 20 0 -50 -25 50 25 0 TEMPERATURE (C) PROG Pin Shutdown Voltage Threshold vs Temperature 5.0 5.0 VCC = 5V 4.5 4.5 VMS(PROG) (V) VMS(PROG) (V) 4.0 3.5 2.5 3.0 -50 2.0 -25 0 25 50 TEMPERATURE (C) 75 100 4069 G20 UW 75 100 4069 G16 Trickle Charge Current vs Supply Voltage VBAT = 2V TA = 25C RPROG = 2k 60 50 40 30 20 Trickle Charge Current vs Temperature VCC = 5V VBAT = 2V RPROG = 2k RPROG = 10k 10 0 -50 RPROG = 10k 4 4.5 5 5.5 SUPPLY VOLTAGE (V) 6 4069 G14 -25 50 25 0 TEMPERATURE (C) 75 100 4069 G15 Timer Accuracy vs Temperature 1 0 -1 VCC = 5V 2.0 1.5 Timer Accuracy vs Supply Voltage TA = 25C 1.0 0.5 0 -0.5 -1.0 -1.5 75 100 4069 G10 -7 -50 -2.0 -25 50 25 TEMPERATURE (C) 0 75 100 4069 G18 4 5 4.5 5.5 SUPPLY VOLTAGE (V) 6 4069 G19 PROG Pin Shutdown Voltage vs Supply Voltage TA = 25C 4.0 3.5 3.0 4 4.5 5 5.5 SUPPLY VOLTAGE (V) 6 4069 G21 4069f 5 LTC4069 PI FU CTIO S GND (Pin 1): Ground. CHRG (Pin 2): Open-Drain Charge Status Output. The charge status indicator pin has three states: pull-down, pulse at 2Hz and high impedance state. This output can be used as a logic interface or as an LED driver. When the battery is being charged, the CHRG pin is pulled low by an internal N-channel MOSFET. When the charge current drops to 10% of the full-scale current, the CHRG pin is forced to a high impedance state. If the battery voltage remains below 2.9V for one quarter of the charge time, the battery is considered defective and the CHRG pin pulses at a frequency of 2Hz (80% duty cycle). When the NTC pin voltage rises above 0.76 * VCC or drops below 0.35 * VCC, the CHRG pin pulses at a frequency of 2Hz (20% duty cycle). BAT (Pin 3): Charge Current Output. Provides charge current to the battery and regulates the final float voltage to 4.2V. An internal precision resistor divider on this pin sets the float voltage and is disconnected in shutdown mode. VCC (Pin 4): Positive Input Supply Voltage. This pin provides power to the charger. VCC can range from 3.75V to 5.5V. This pin should be bypassed with at least a 1F capacitor. When VCC is within 32mV of the BAT pin voltage, the LTC4069 enters shutdown mode, dropping IBAT to about 1A. NTC (Pin 5): Input to the NTC (Negative Temperature Coefficient) Thermistor Temperature Monitoring Circuit. Under normal operation, connect a thermistor from the NTC pin to ground and a resistor of equal value from the NTC pin to VCC. When the voltage at this pin drops below 0.35 * VCC at hot temperatures or rises above 0.76 * VCC at cold, charging is suspended, the internal timer is frozen and the CHRG pin output will start to pulse at 2Hz. Pulling this pin below 0.016 * VCC disables the NTC feature. There is approximately 3C of temperature hysteresis associated with each of the input comparator's thresholds. PROG (Pin 6): Charge Current Program and Charge Current Monitor Pin. Connecting a 1% resistor, RPROG, to ground programs the charge current. When charging in constant-current mode, this pin servos to 1V. In all modes, the voltage on this pin can be used to measure the charge current using the following formula: IBAT = VPROG * 1000 RPROG 6 U U U Floating the PROG pin puts the charger in shutdown mode. In shutdown mode, the LTC4069 has less than 20A supply current and about 1A battery drain current. Exposed Pad (Pin 7): Ground. The Exposed Pad must be soldered to the PCB ground to provide both electrical contact and rated thermal performance. 4069f LTC4069 SI PLIFIED BLOCK DIAGRA VCC R7 115C TDIE + TA - M2 1x M1 1000x 3.6V C1 VCC RNOM NTC 5 RNTC R9 R8 TOO COLD OR AND SUSPEND D1 + C2 - + C3 TOO HOT CA NTC_EN MP REF 1.2V R3 1V R4 0.1V R5 ENABLE MIN SUSPEND LOGIC COUNTER CHARGE CONTROL R2 1.2V - R10 PROG 0.1V + C/10 - 2.9V BAT OPERATIO The LTC4069 is a linear battery charger designed primarily for charging single cell lithium-ion batteries. Featuring an internal P-channel power MOSFET, the charger uses a constant-current/constant-voltage charge algorithm with programmable current. Charge current can be programmed up to 750mA with a final float voltage accuracy of 0.6%. The CHRG open-drain status output indicates if C/10 has been reached. No blocking diode or external sense resistor is required; thus, the basic charger circuit requires only two external components. An internal termination timer and trickle charge low-battery conditioning adhere to battery manufacturer safety guidelines. Furthermore, the + - 2 CHRG + LOBAT 4V PROG 6 RPROG 1 C4 SHUTDOWN - GND OSCILLATOR 4069 F01 Figure 1. LTC4069 Block Diagram LTC4069 is capable of operating from a USB power source. An internal thermal limit reduces the programmed charge current if the die temperature attempts to rise above a preset value of approximately 115C. This feature protects the LTC4069 from excessive temperature and allows the user to push the limits of the power handling capability of a given circuit board without risk of damaging the LTC4069 or external components. Another benefit of the LTC4069 thermal limit is that charge current can be set according to typical, not worst-case, ambient temperatures for a given 4069f - + + - W VCC 4 VCC D3 + - U W + C5 UVLO - D2 BAT 3 - MA + R1 VA + 7 LTC4069 OPERATIO application with the assurance that the charger will automatically reduce the current in worst-case conditions. The charge cycle begins when the voltage at the VCC pin rises above 3.5V and approximately 80mV above the BAT pin voltage, a 1% program resistor is connected from the PROG pin to ground and the NTC pin voltage stays between 0.76 * VCC and 0.35 * VCC or below 0.016 * VCC. If the BAT pin voltage is below 2.9V, the charger goes into trickle charge mode, charging the battery at one-tenth the programmed charge current to bring the cell voltage up to a safe level for charging. If the BAT pin voltage is above 4.1V, the charger will not charge the battery as the cell is near full capacity. Otherwise, the charger goes into the fast charge constant-current mode. When the BAT pin approaches the final float voltage (4.2V), the LTC4069 enters constant-voltage mode and the charge current begins to decrease. When the current drops to 10% of the full-scale charge current, an internal comparator turns off the N-channel MOSFET on the CHRG pin and the pin assumes a high impedance state. An internal timer sets the total charge time, tTIMER (typically 4.5 hours). When this time elapses, the charge cycle terminates and the CHRG pin assumes a high impedance state. The charge cycle will automatically restart if the BAT pin voltage falls below VRECHRG (typically 4.1V). To manually restart the charge cycle, remove the input voltage and reapply it, or momentarily float the PROG pin and reconnect it. Programming Charge Current The charge current is programmed using a single resistor from the PROG pin to ground. The battery charge current is 1000 times the current out of the PROG pin. The program resistor and the charge current are calculated using the following equations: RPROG = 1000 * The charge current out of the BAT pin can be determined at any time by monitoring the PROG pin voltage and using the following equation: 8 U IBAT = VPROG * 1000 RPROG Undervoltage Lockout (UVLO) An internal undervoltage lockout circuit monitors the input voltage and keeps the charger in undervoltage lockout until VCC rises above 3.6V and approximately 80mV above the BAT pin voltage. The 3.6V UVLO circuit has a built-in hysteresis of approximately 0.6V and the automatic shutdown threshold has a built-in hysteresis of approximately 50mV. During undervoltage lockout conditions, maximum battery drain current is 4A and maximum supply current is 11A. Shutdown Mode The LTC4069 can be disabled by floating the PROG pin. In shutdown mode, the battery drain current is reduced to less than 1A and the supply current to about 20A. Timer and Recharge The LTC4069 has an internal termination timer that starts when an input voltage greater than the undervoltage lockout threshold is applied to VCC, or when leaving shutdown and the battery voltage is less than the recharge threshold. At power-up or when exiting shutdown, if the battery voltage is less than the recharge threshold, the charge time is set to 4.5 hours. If the battery temperature is either too high or too low, the timer will pause until the battery returns to normal temperature. If the battery is greater than the recharge threshold at power-up or when exiting shutdown, the timer will not start and charging is prevented since the battery is at or near full capacity. Once the charge cycle terminates, the LTC4069 continuously monitors the BAT pin voltage using a comparator with a 2ms filter time. When the battery voltage falls below 4.1V (which corresponds to 80% to 90% battery capacity), a new charge cycle is initiated and a 2.25 hour timer begins. This ensures that the battery is kept at, or near, a fully charged condition and eliminates the need for periodic charge cycle initiations. Also, if the battery voltage 4069f 1V ICHG , ICHG = 1000 V RPROG LTC4069 OPERATIO does not exceed the recharge threshold voltage when the timer ends, the timer resets and a 2.25 hour recharge cycle begins. The CHRG output assumes a strong pull-down state during recharge cycles until C/10 is reached when it transitions to a high impendance state. Trickle Charge and Defective Battery Detection At the beginning of a charge cycle, if the battery voltage is low (below 2.9V), the charger goes into trickle charge, reducing the charge current to 10% of the full-scale current. If the low-battery voltage persists for one quarter of the total time (1.125 hour), the battery is assumed to be defective, the charge cycle is terminated and the CHRG pin output pulses at a frequency of 2Hz with a 80% duty cycle. If for any reason the battery voltage rises above 2.9V, the charge cycle will be restarted. To restart the charge cycle (i.e., when the defective battery is replaced with a discharged battery), simply remove the input voltage and reapply it or momentarily float the PROG pin and reconnect it. CHRG Status Output Pin The charge status indicator pin has three states: pulldown, pulse at 2Hz (see Trickle Charge and Defective Battery Detection and Battery Temperature Monitoring) and high impedance. The pull-down state indicates that the LTC4069 is in a charge cycle. A high impedance state indicates that the charge current has dropped below 10% of the full-scale current or the LTC4069 is disabled. Figure 2 shows the CHRG status under various conditions. Charge Current Soft-Start and Soft-Stop The LTC4069 includes a soft-start circuit to minimize the inrush current at the start of a charge cycle. When a charge cycle is initiated, the charge current ramps from zero to the full-scale current over a period of approximately 170s. Likewise, internal circuitry slowly ramps the charge current from full-scale to zero when the charger is shut off or self terminates. This has the effect of minimizing the transient current load on the power supply during start-up and charge termination. U Constant-Current/Constant-Voltage/ Constant-Temperature The LTC4069 uses a unique architecture to charge a battery in a constant-current, constant-voltage and constant-temperature fashion. Figure 1 shows a Simplified Block Diagram of the LTC4069. Three of the amplifier feedback loops shown control the constant-current (CA), constant-voltage (VA), and constant-temperature (TA) modes. A fourth amplifier feedback loop (MA) is used to increase the output impedance of the current source pair, M1 and M2 (note that M1 is the internal P-channel power MOSFET). It ensures that the drain current of M1 is exactly 1000 times greater than the drain current of M2. Amplifiers CA and VA are used in separate feedback loops to force the charger into constant-current or constantvoltage mode, respectively. Diodes D1 and D2 provide priority to either the constant-current or constant-voltage loop, whichever is trying to reduce the charge current the most. The output of the other amplifier saturates low which effectively removes its loop from the system. When in constant-current mode, CA servos the voltage at the PROG pin to be precisely 1V. VA servos its inverting input to an internal reference voltage when in constant-voltage mode and the internal resistor divider, made up of R1 and R2, ensures that the battery voltage is maintained at 4.2V. The PROG pin voltage gives an indication of the charge current during constant-voltage mode as discussed in "Programming Charge Current". Transconductance amplifier, TA, limits the die temperature to approximately 115C when in constant-temperature mode. Diode D3 ensures that TA does not affect the charge current when the die temperature is below approximately 115C. The PROG pin voltage continues to give an indication of the charge current. In typical operation, the charge cycle begins in constantcurrent mode with the current delivered to the battery equal to 1000V/RPROG. If the power dissipation of the LTC4069 results in the junction temperature approaching 115C, the amplifier (TA) will begin decreasing the charge current to limit the die temperature to approximately 115C. As the battery voltage rises, the LTC4069 either returns to constant-current mode or enters constantvoltage mode straight from constant-temperature mode. 4069f 9 LTC4069 OPERATIO POWER ON Regardless of mode, the voltage at the PROG pin is proportional to the current delivered to the battery. Battery Temperature Monitoring via NTC The battery temperature is measured by placing a negative temperature coefficient (NTC) thermistor close to the battery pack. The NTC circuitry is shown in Figure 3. To use this feature, connect the NTC thermistor, RNTC, between the NTC pin and ground and a resistor, RNOM, from the NTC pin to VCC. RNOM should be a 1% resistor with a value equal to the value of the chosen NTC thermistor at 25C (this value is 10k for a Vishay NTHS0603NO1N1002J thermistor). The LTC4069 goes into hold mode when the value of the NTC thermistor drops to 0.53 times the value of RNOM, which corresponds to 10 U UVLO NO IF VCC > 3.6V AND VCC > VBAT + 80mV? CHRG HIGH IMPEDANCE UVLO MODE YES NTC FAULT TEMPERATURE NOT OK BATTERY CHARGING SUSPENDED CHRG PULSES (2Hz) TEMPERATURE OK 2.9V < VBAT < 4.1V FAST CHARGE MODE FULL CHARGE CURRENT CHRG STRONG PULL-DOWN NO CHARGE CYCLE (4.5 HOURS) RECHARGE IS VBAT < 4.1V? NO VBAT > 4.1V STANDBY MODE NO CHARGE CURRENT CHRG HIGH IMPEDANCE TEMPERATURE NOT OK VBAT 2.9V TRICKLE CHARGE MODE 1/10 FULL CHARGE CURRENT CHRG STRONG PULL-DOWN 1/4 CHARGE CYCLE (1.125 HOURS) DEFECTIVE BATTERY IS VBAT < 2.9V? YES BAD BATTERY MODE NO CHARGE CURRENT CHRG PULSES (2Hz) VCC < 3V YES RECHARGE MODE FULL CHARGE CURRENT CHRG STRONG PULL-DOWN 1/2 CHARGE CYCLE (2.25 HOURS) 4069 F02 Figure 2. State Diagram of LTC4069 Operation approximately 40C, and when the value of the NTC thermistor increases to 3.26 times the value of RNOM, which corresponds to approximately 0C. Hold mode freezes the timer and stops the charge cycle until the thermistor indicates a return to a valid temperature. For a Vishay NTHS0603NO1N1002J thermistor, this value is 32.6k which corresponds to approximately 0C. The hot and cold comparators each have approximately 3C of hysteresis to prevent oscillation about the trip point. When the charger is in Hold mode (battery temperature is either too hot or too cold) the CHRG pin pulses in a 2Hz, 20% duty cycle frequency unless the charge task is finished or the battery is assumed to be defective. If the NTC pin is grounded, the NTC function will be disabled. 4069f LTC4069 OPERATIO 0.76 * VCC NTC 6 0.35 * VCC 0.016 * VCC - Figure 3. NTC Circuit Information APPLICATIO S I FOR ATIO Undervoltage Charge Current Limiting (UVCL) The LTC4069 includes undervoltage charge (VUVCL1) current limiting that prevents full charge current until the input supply voltage exceeds approximately 200mV above the battery voltage. This feature is particularly useful if the LTC4069 is powered from a supply with long leads (or any relatively high output impedance). For example, USB-powered systems tend to have highly variable source impedances (due primarily to cable quality and length). A transient load combined with such impedance can easily trip the UVLO threshold and turn the charger off unless undervoltage charge current limiting is implemented. Consider a situation where the LTC4069 is operating under normal conditions and the input supply voltage begins to droop (e.g., an external load drags the input supply down). If the input voltage reaches VBAT + VUVCL1 (approximately 220mV above the battery voltage), undervoltage charge current limiting will begin to reduce the charge current in an attempt to maintain VUVCL1 between the VCC input and the BAT output of the IC. The + - RNTC + - U W UU U VCC RNOM TOO COLD TOO HOT + NTC_ENABLE 4069 F03 LTC4069 will continue to operate at the reduced charge current until the input supply voltage is increased or constant voltage mode reduces the charge current further. Operation from Current Limited Wall Adapter By using a current limited wall adapter as the input supply, the LTC4069 dissipates significantly less power when programmed for a current higher than the limit of the supply as compared to using a non-current limited supply at the same charge current. Consider a situation where an application demands a 600mA charge current for an 800mAh Li-Ion battery. If a typical 5V (non-current limited) input supply is used, the charger's peak power dissipation can exceed 1W. Now consider the same scenario, but with a 5V input supply with a 600mA current limit. To take advantage of the current limited supply, it is necessary to program the LTC4069 to charge at a current above 600mA. Assume that the LTC4069 is programmed for 750mA (i.e., RPROG = 1.33k) to ensure that part tolerances maintain a programmed current higher than 600mA. Since the LTC4069 4069f 11 LTC4069 APPLICATIO S I FOR ATIO will demand a charge current higher than the current limit of the voltage supply, the supply voltage will drop to the battery voltage plus 600mA times the "on" resistance of the internal PFET. The "on" resistance of the LTC4069 power device is approximately 450m with a 5V supply. The actual "on" resistance will be slightly higher due to the fact that the input supply will drop to less than 5V. The power dissipated during this phase of charging is less than 240mW. That is a 76% improvement over the non-current limited supply power dissipation. USB and Wall Adapter Power Although the LTC4069 allows charging from a USB port, a wall adapter can also be used to charge Li-Ion batteries. Figure 4 shows an example of how to combine wall adapter and USB power inputs. A P-channel MOSFET, MP1, is used to prevent back conducting into the USB port when a wall adapter is present and Schottky diode, D1, is used to prevent USB power loss through the 1k pull-down resistor. Typically a wall adapter can supply significantly more current than the 500mA-limited USB port. Therefore, an N-channel MOSFET, MN1, and an extra program resistor are used to increase the charge current to 750mA when the wall adapter is present. Stability Considerations The LTC4069 contains two control loops: constant-voltage and constant-current. The constant-voltage loop is stable without any compensation when a battery is connected with low impedance leads. Excessive lead length, however, may add enough series inductance to require a 5V WALL ADAPTER 750mA ICHG USB POWER 500mA ICHG ICHG BAT D1 MP1 LTC4069 VCC PROG MN1 4.02k 1k 4069 F04 + Li-Ion BATTERY 2k Figure 4. Combining Wall Adapter and USB Power 12 U bypass capacitor of at least 1F from BAT to GND. Furthermore, a 4.7F capacitor with a 0.2 to 1 series resistor from BAT to GND is required to keep ripple voltage low when the battery is disconnected. High value capacitors with very low ESR (especially ceramic) may reduce the constant-voltage loop phase margin. Ceramic capacitors up to 22F may be used in parallel with a battery, but larger ceramics should be decoupled with 0.2 to 1 of series resistance. In constant-current mode, the PROG pin is in the feedback loop, not the battery. Because of the additional pole created by the PROG pin capacitance, capacitance on this pin must be kept to a minimum. With no additional capacitance on the PROG pin, the charger is stable with program resistor values as high as 25k. However, additional capacitance on this node reduces the maximum allowed program resistor. The pole frequency at the PROG pin should be kept above 100kHz. Therefore, if the PROG pin is loaded with a capacitance, CPROG, the following equation should be used to calculate the maximum resistance value for RPROG: RPROG 1 2 * 105 * CPROG Average, rather than instantaneous, battery current may be of interest to the user. For example, if a switching power supply operating in low current mode is connected in parallel with the battery, the average current being pulled out of the BAT pin is typically of more interest than the instantaneous current pulses. In such a case, a simple RC filter can be used on the PROG pin to measure the average SYSTEM LOAD LTC4069 PROG GND RPROG 4069 F05 W UU 10k CFILTER CHARGE CURRENT MONITOR CIRCUITRY Figure 5. Isolating Capacitive Load on the PROG Pin and Filtering 4069f LTC4069 APPLICATIO S I FOR ATIO battery current as shown in Figure 5. A 10K resistor has been added between the PROG pin and the filter capacitor to ensure stability. Power Dissipation The conditions that cause the LTC4069 to reduce charge current through thermal feedback can be approximated by considering the power dissipated in the IC. For high charge currents, the LTC4069 power dissipation is approximately: PD = (VCC - VBAT) * IBAT where PD is the power dissipated, VCC is the input supply voltage, VBAT is the battery voltage and IBAT is the charge current. It is not necessary to perform any worst-case power dissipation scenarios because the LTC4069 will automatically reduce the charge current to maintain the die temperature at approximately 115C. However, the approximate ambient temperature at which the thermal feedback begins to protect the IC is: TA = 115C - PD * JA TA = 115C - (VCC - VBAT) * IBAT * JA Example: Consider an LTC4069 operating from a 5V wall adapter providing 750mA to a 3.6V Li-Ion battery. The ambient temperature above which the LTC4069 will begin to reduce the 750mA charge current is approximately: TA = 115C - (5V - 3.6V) * (750mA) * 60C/W TA = 115C - (1.05W * 60C/W) = 115C - 63C TA = 52C The LTC4069 can be used above 70C, but the charge current will be reduced from 750mA. The approximate current at a given ambient temperature can be calculated: IBAT = 115C - TA ( VCC - VBAT ) * JA U Using the previous example with an ambient temperature of 73C, the charge current will be reduced to approximately: IBAT = 115C - 73C 42C = = 500mA (5V - 3.6V ) * 60C/W 84C/A W UU Furthermore, the voltage at the PROG pin will change proportionally with the charge current as discussed in the Programming Charge Current section. It is important to remember that LTC4069 applications do not need to be designed for worst-case thermal conditions since the IC will automatically limit power dissipation when the junction temperature reaches approximately 115C. Board Layout Considerations In order to deliver maximum charge current under all conditions, it is critical that the exposed metal pad on the backside of the LTC4069 package is soldered to the PC board copper and extending out to relatively large copper areas or internal copper layers connected using vias. Correctly soldered to a 2500mm2 double-sided 1 oz. copper board the LTC4069 has a thermal resistance of approximately 60C/W. Failure to make thermal contact between the Exposed Pad on the backside of the package and the copper board will result in thermal resistances far greater than 60C/W. As an example, a correctly soldered LTC4069 can deliver over 750mA to a battery from a 5V supply at room temperature. Without a backside thermal connection, this number could drop to less than 500mA. VCC Bypass Capacitor Many types of capacitors can be used for input bypassing; however, caution must be exercised when using multilayer ceramic capacitors. Because of the self-resonant and high Q characteristics of some types of ceramic capacitors, high voltage transients can be generated under some start-up conditions, such as connecting the charger input to a live power source. For more information, refer to Application Note 88. 4069f 13 LTC4069 APPLICATIO S I FOR ATIO VCC RNOM 8.87k 0.76 * VCC NTC TOO COLD 6 R1 604 RNTC 10k 0.35 * VCC TOO HOT + NTC_ENABLE 0.016 * VCC - Figure 6. NTC Circuits Thermistors The LTC4069 NTC trip points are designed to work with thermistors whose resistance-temperature characteristics follow Vishay Dale's "R-T Curve 1." The Vishay NTHS0603NO1N1002J is an example of such a thermistor. However, Vishay Dale has many thermistor products that follow the "R-T Curve 1" characteristic in a variety of sizes. Furthermore, any thermistor whose ratio of RCOLD to RHOT is about 5 will also work (Vishay Dale R-T Curve 1 shows a ratio of RCOLD to RHOT of 3.266/0.5325 = 6.13). Power conscious designs may want to use thermistors whose room temperature value is greater than 10k. Vishay Dale has a number of values of thermistor from 10k to 100k that follow the "R-T Curve 1." Using different R-T curves, such as Vishay Dale "R-T Curve 2", is also possible. This curve, combined with LTC4069 internal thresholds, gives temperature trip points of approximately 0C (falling) and 40C (rising), a delta of 40C. This delta in temperature can be moved in either direction by changing the value of RNOM with respect to RNTC. Increasing RNOM will move both trip points to higher temperatures. To 14 U calculate RNOM for a shift to lower temperature for example, use the following equation: RNOM = RCOLD * RNTC at 25 C 3 . 266 W + + - - UU where RCOLD is the resistance ratio of RNTC at the desired cold temperature trip point. If you want to shift the trip points to higher temperatures use the following equation: RNOM = RHOT * RNTC at 25 C 0 . 5325 where RHOT is the resistance ratio of RNTC at the desired hot temperature trip point. Here is an example using a 100k R-T Curve 2 thermistor from Vishay Dale. The difference between the trip points is 40C, from before, and we want the cold trip point to be 0C, which would put the hot trip point at 40C. The RNOM needed is calculated as follows: RNOM = = RCOLD * RNTC at 25 C 3 . 266 2 . 816 * 10k = 8 . 62k 3 . 266 4069 F06 The nearest 1% value for RNOM is 8.66k. This is the value used to bias the NTC thermistor to get cold and hot trip points of approximately 0C and 40C respectively. To extend the delta between the cold and hot trip points, a resistor, R1, can be added in series with RNTC (see Figure 6). The values of the resistors are calculated as follows: RNOM = RCOLD - RHOT 3 . 266 - 0 . 5325 0 . 5325 * (RCOLD - RHOT ) - RHOT R1 = 3 . 266 - 0 . 5325 where RNOM is the value of the bias resistor and RHOT and RCOLD are the values of RNTC at the desired temperature trip points. Continuing the example from before with a desired trip point of 50C: 4069f LTC4069 APPLICATIO S I FOR ATIO 10k * ( 2.816 - 0.4086 ) 4 R -R R = COLD HOT = NOM 3.266 - 0.5325 3.266 - 0.5325 = 8.8k, 8.87k is the nearest 1% value. 0.5325 R1 = 10k * * ( 2.816 - 0.4086 ) - 0.4086 3.266 - 0.5325 = 604, 604 is the nearest 1% value. NTC Trip Point Error When a 1% resistor is used for RHOT, the major error in the 40C trip point is determined by the tolerance of the NTC thermistor. A typical 100k NTC thermistor has 10% tolerance. By looking up the temperature coefficient of the thermistor at 40C, the tolerance error can be calculated in degrees centigrade. Consider the Vishay NTHS0603N01N1003J thermistor, which has a temperature coefficient of -4%/C at 40C. Dividing the tolerance by the temperature coefficient, 5%/(4%/C) = 1.25C, gives the temperature error of the hot trip point. PACKAGE DESCRIPTIO DC Package 6-Lead Plastic DFN (2mm x 2mm) (Reference LTC DWG # 05-08-1703) R = 0.115 TYP 0.56 0.05 (2 SIDES) 2.00 0.10 (4 SIDES) PIN 1 CHAMFER OF EXPOSED PAD 3 0.25 0.05 0.50 BSC 1.42 0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WCCD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 4069f 0.675 0.05 2.50 0.05 1.15 0.05 0.61 0.05 (2 SIDES) PACKAGE OUTLINE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U The cold trip point error depends on the tolerance of the NTC thermistor and the degree to which the ratio of its value at 0C and its value at 40C varies from 6.14 to 1. Therefore, the cold trip point error can be calculated using the tolerance, TOL, the temperature coefficient of the thermistor at 0C, TC (in %/C), the value of the thermistor at 0C, RCOLD, and the value of the thermistor at 40C, RHOT. The formula is: U W UU Temperature Error(C) = 1+ TOL RCOLD - 1 * 100 6.14 * R HOT TC For example, the Vishay NTHS0603N01N1003J thermistor with a tolerance of 5%, TC of -5%/C and RCOLD/RHOT of 6.13, has a cold trip point error of: 1+ 0.05 6.14 * 6.13 - 1 * 100 Temperature Error(C) = -5 = -0.95C, 1.05C 0.38 0.05 4 6 PIN 1 BAR TOP MARK (SEE NOTE 6) 1 (DC6) DFN 1103 0.200 REF 0.75 0.05 0.25 0.05 0.50 BSC 1.37 0.05 (2 SIDES) 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD 15 LTC4069 RELATED PARTS PART NUMBER Battery Chargers LTC1734 LTC1734L LTC4002 LTC4050 LTC4052 LTC4053 LTC4054 LTC4057 LTC4058 LTC4059/LTC4059A LTC4061 LTC4061-4.4 LTC4062 LTC4063 LTC4065/LTC4065A LTC4411/LTC4412 Power Management LTC3405/LTC3405A LTC3406/LTC3406A LTC3411 LTC3440 LTC4413 300mA (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter 600mA (IOUT), 1.5MHz, Synchronous Step-Down DC/DC Converter 1.25A (IOUT), 4MHz, Synchronous Step-Down DC/DC Converter 600mA (IOUT), 2MHz, Synchronous Buck-Boost DC/DC Converter Dual Ideal Diode in DFN 95% Efficiency, VIN: 2.7V to 6V, VOUT = 0.8V, IQ = 20A, ISD < 1A, ThinSOT Package 95% Efficiency, VIN: 2.5V to 5.5V, VOUT = 0.6V, IQ = 20A, ISD < 1A, ThinSOT Package 95% Efficiency, VIN: 2.5V to 5.5V, VOUT = 0.8V, IQ = 60A, ISD < 1A, MS Package 95% Efficiency, VIN: 2.5V to 5.5V, VOUT = 2.5V, IQ = 25A, ISD < 1A, MS Package 2-Channel Ideal Diode ORing, Low Forward ON Resistance, Low Regulated Forward Voltage, 2.5V VIN 5.5V Lithium-Ion Linear Battery Charger in ThinSOTTM Lithium-Ion Linear Battery Charger in ThinSOT Switch Mode Lithium-Ion Battery Charger Lithium-Ion Linear Battery Charger Controller Monolithic Lithium-Ion Battery Pulse Charger USB Compatible Monolithic Li-Ion Battery Charger Standalone Linear Li-Ion Battery Charger with Integrated Pass Transistor in ThinSOT Lithium-Ion Linear Battery Charger Standalone 950mA Lithium-Ion Charger in DFN 900mA Linear Lithium-Ion Battery Charger Standalone Li-Ion Charger with Thermistor Interface Standalone Li-Ion Charger with Thermistor Interface Standalone Linear Li-Ion Battery Charger with Micropower Comparator Li-Ion Charger with Linear Regulator Standalone Li-Ion Battery Charger Low Loss PowerPathTM Controller in ThinSOT Simple ThinSOT Charger, No Blocking Diode, No Sense Resistor Needed Low Current Version of LTC1734, 50mA ICHRG 180mA Standalone, 4.7V VIN 24V, 500kHz Frequency, 3 Hour Charge Termination Features Preset Voltages, C/10 Charger Detection and Programmable Timer, Input Power Good Indication, Thermistor Interface No Blocking Diode or External Power FET Required, 1.5A Charge Current Standalone Charger with Programmable Timer, Up to 1.25A Charge Current Thermal Regulation Prevents Overheating, C/10 Termination, C/10 Indicator, Up to 800mA Charge Current Up to 800mA Charge Current, Thermal Regulation, ThinSOT Package C/10 Charge Termination, Battery Kelvin Sensing, 7% Charge Accuracy 2mm x 2mm DFN Package, Thermal Regulation, Charge Current Monitor Output, Version A has ACPR Function 4.2V, 0.35% Float Voltage, Up to 1A Charge Current, 3mm x 3mm DFN 4.4V (Max), 0.4% Float Voltage, Up to 1A Charge Current, 3mm x 3mm DFN 4.2V, 0.35% Float Voltage, Up to 1A Charge Current, 3mm x 3mm DFN Up to 1A Charge Current, 100mA, 125mV LDO, 3mm x 3mm DFN 4.2V, 0.6% Float Voltage, Up to 750mA Charge Current, 2mm x 2mm DFN, Version A has ACPR Function Automatic Switching Between DC Sources, Load Sharing, Replaces ORing Diodes DESCRIPTION COMMENTS ThinSOT and PowerPath are trademarks of Linear Technology Corporation. 4069f 16 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 LT 1105 * PRINTED IN THE USA www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2005 |
Price & Availability of LTC4069NBSP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |